Your cart is currently empty!
IPS112-X Viper Billet Hub Centric Wheel Spacer with External Hub
Viper .420 Thick Hub Centric Wheel Spacer with External Hub for wheel registration – Fits all Dodge Vipers
CNC machined from aircraft 6061-T6 Aluminum, available in .420″ thick, 6 X 4.50 bolt pattern.
All of our wheel spacers are hub centric, as they register on the bearing hub not the wheel studs. These wheel spacers have an external hub for registering the wheel on and insure there is enough material to support the wheel and not be knocked off due to a thin web between the internal bore and external hub.
Sold as singles, picture shows internal hub registration and external wheel registration
$78.00
In StockDescription
Viper .420 Thick Hub Centric Wheel Spacer with External Hub for wheel registration – Fits all Dodge Vipers
CNC machined from aircraft 6061-T6 Aluminum, available in .420″ thick, 6 X 4.50 bolt pattern.
All of our wheel spacers are hub centric, as they register on the bearing hub not the wheel studs. These wheel spacers have an external hub for registering the wheel on and insure there is enough material to support the wheel and not be knocked off due to a thin web between the internal bore and external hub.
(** Note: When using wheel spacers, you must use Extended Lug Nuts to make up for lost stud threads on spacer less than .420″ thick. Spacers over .420″ REQUIRE longer axle studs to be installed. **)
Call for Custom thickness needed
All of our wheel spacers are hub-centric by registering on the wheel hub not the wheel studs. Lug Nuts should be tightened in a pattern shown below and torque in 3 steps to help insure wheel centering when lug nuts are tight. “Note: Wheel Spacers fill a cosmetic purpose, not a performance modification. Some sanctioning bodies exclude wheel spacers from HPDE track or competition events.”
Â
Â
Additional information
| Weight | 2 lbs |
|---|---|
| Dimensions | 6 × 6 × 4 in |
| Thickness | .420", Custom |
You may also like…
-
Viper PartsIPS189 – Lug Nuts – Extended
Extended Lug Nuts to use with Spacer Plates
Custom lug nuts that extend into the wheel to gain back threads that were lost by adding spacer plates. 1/2-20 thread, 3/4 Hex. Available in Chrome or Black.Â
(MUST USE ANTI-SEIZE LUBRICANT or WD40 ON WHEEL STUDS TO HELP PREVENT THREAD GALLING (COLD WELDING OF THE THREADS)
Sold in Sets of 6
(0 reviews)$15.00 – $21.00 Select options This product has multiple variants. The options may be chosen on the product page
Related products
-
Viper Parts
IPS220 Front & Rear Tow Hook Set – 1992-2002
GEN 1&2 Front & Rear Tow Hook Set
These tow hooks make it easy to trailer load your car, and for the racer, a tow point to get you out of the sand traps. Front tow hook mounts to existing bolts, and takes less than 10 minutes to install. The rear hook requires 2 holes to be drilled into the lower rear frame rail. Unlike other rear tow hook kits out there, this uses a sandwich design which will not collapse the frame rails due to no internal box support. Also the installation is easier because you are not trying to drill through two sides of the frame rail at an angle.
(0 reviews)$91.00 – $175.00 Select options This product has multiple variants. The options may be chosen on the product page -
Viper Parts
Front Tow Hook Kits – GEN 5 Vipers 2013-2017
GEN 5 Front Tow Hooks
The Front Tow Hook kits are made from 6061-T6 Aluminum, and weighs only 2 LBS. Its design is stronger and distributes the load over a greater area unlike other steel versions on the market. The complete kit installs in less than 30 minutes, and when needed the Tow Ring can then be installed or removed in less than 2 minutes, so you don’t run into it when walking around the front of the car.
Front Fixed Ring Front Removable Tow Hook Kit – Design is a fixed Ring Plate
Front Flex Ring Front Removable Tow Hook Kit – Â design allows for the pulling force on the ring to adjust to the angle of the pull automatically.
(0 reviews)$241.00 – $271.00 Select options This product has multiple variants. The options may be chosen on the product page -
Viper Parts
IPS150-Low Billet Transmission Cross Member 96-02 Vipers
Viper Billet Transmission Cross Member 96-02 Vipers Low cut Version for Polyurethane Mount
This one piece, billet cross member is designed to remove flex that the factory cross member can have. It improves shifting and overall chassis strength, while reducing unwanted vibrations. Machined from a solid block of aircraft 6061-T6 aluminum. Should also add the Polyurethane Mount option to get the best performance improvement.
(0 reviews) -
Viper Parts
IPS168 Replacement Wheel Centers
Replacement wheel centers CNC machined from aircraft 6061 – T6 Aluminum, available in polished plain domed, or black anodized with or without Logo. Center caps come with safety rings to insure they do not come out of the wheel.
(0 reviews)$188.00 – $223.00 Select options This product has multiple variants. The options may be chosen on the product page
Reviews
There are no reviews yet.