Your cart is currently empty!
IPS220 Front & Rear Tow Hook Set – 1992-2002
GEN 1&2 Front & Rear Tow Hook Set
These tow hooks make it easy to trailer load your car, and for the racer, a tow point to get you out of the sand traps. Front tow hook mounts to existing bolts, and takes less than 10 minutes to install. The rear hook requires 2 holes to be drilled into the lower rear frame rail. Unlike other rear tow hook kits out there, this uses a sandwich design which will not collapse the frame rails due to no internal box support. Also the installation is easier because you are not trying to drill through two sides of the frame rail at an angle.
$91.00 – $175.00
In StockDescription
GEN 1&2 Front & Rear Tow Hook Set
These tow hooks make it easy to trailer load your car, and for the racer, a tow point to get you out of the sand traps. Front tow hook mounts to existing bolts, and takes less than 10 minutes to install. The rear hook requires 2 holes to be drilled into the lower rear frame rail. Unlike other rear tow hook kits out there, this uses a sandwich design which will not collapse the frame rails due to no internal box support. Also the installation is easier because you are not trying to drill through two sides of the frame rail at an angle.
IPS220 GEN 2 Front & Rear Tow Hook Installation Instructions
Additional information
| Weight | 4 lbs |
|---|---|
| Dimensions | 12 × 4 × 4 in |
| OPTIONS | FRONT ONLY, REAR ONLY, BOTH FRONT & REAR |
Related products
-
Viper PartsIPS139-X Shift Knob adapter
This adapter can be used to allow the use of many after market knob available from your local auto part dealers. Make from 303 Stainless Steel adapts from 1/2″-20 Female therad to 1/2″-20 Male thread, with boot groove.
(0 reviews)$39.00 – $42.00 Select options -
Viper Parts
IPS173-GEN 1/2 Billet Pulleys 92-02 Vipers
Gen 1/2Â Billet Pulleys 92-02 Vipers
ALT Pulley
Replaces the Factory Steel Pulley with a Billet Aluminum Pulley.
Idler Pulley
Replaces the Factory Steel Pulley with a Billet Aluminum Pulley with a replaceable Bearing.
Belt Tensioner Pulley
Replaces the Factory Plastic Tensioner Pulley with a Billet Aluminum Pulley with a replaceable Bearing.
Power Steering Pump Pulley
Replaces the Factory Plastic Pulley that will fail at some point. The replacement is made from Billet Aluminum. The Pulley utilizes a self-locking hub design so no Pullers are required to install or remove the pulley hub on pump shaft.
Under Drive Crank Pulley
Pulley is designed to turn water pump, Alternator, Power Steering pump, & AC 25% slower. This results is a 5-10HP gain and keeps the water pump from cavitation problems, and includes new 5/16 – 18 Grade 8 mounting hardware.
Water Pump Pulley 5.4″ Dia.
(0 reviews)$54.00 – $241.00 Select options -
Viper Parts
IPS143X Seat Lowering Kit Fixed 2″ – 03-10 Vipers
Seat Lowering Kit – Fixed 2″Â 03-10 Vipers
This fixed seat lowering kit lowers the 03-10 SRT seat a full 2 inches, allowing extra knee room and headroom for even the tallest Viper driver. The seat will no longer slide forward or backwards, but the seat back can be tilted.
2008-2010 owners *** IMPORTANT AIRBAG FACTS ***
Decision regarding seat lowering and air bag operation for both seats on 08-10 SRT10 Vipers.
Both passenger seats have a new system in the Viper that will correctly determine the weight of an occupant and adjust the airbag to on or off. It has some criteria to be met though as it is MUCH more advanced than any system has been before it.
Between 65 and 105 pounds the system will determine the need for the airbag at all. This will be based on a correctly seated person! This is true for all the levels of adjustment. You must sit in the seat correctly and distribute your weight evenly in the seat without leaning for/aft or side to side. Within seconds after starting the car the system will “lock in” your values. If this is not done correctly and the light is incorrect for your weight it is best to exit the running vehicle and wait 2-6 minutes before re entering the vehicle. At 2 minutes the corrected value is 80% and as the minutes increase to 6 minutes the corrected percentage gets closer to 100. The system also monitors and updates your weight and “position” in the vehicle every 2 minutes after that.
At 120+ pounds the airbag will still be monitored by the system but will be in the ON mode. It is still critical that your weight is evenly distributed though as it senses this every 2 minutes.
This all being said if you install the seat lowering kit you will need to do the following:
Both seats have a position sensor located under the seat, that controls the air bag by proximity to the steering wheel for force adjustment.
If the seat is lowered and the switch is not installed correctly the force of the airbag is unknown but it WILL still deploy if the conditions are met for it. The seat position sensor (a metal proximity sensor), will need to be adjacent to metal when the seat is from midway to the far back position, so you will need to zip tied it to the metal frame of the seat. The purpose of this sensor is to either reduce the air bag charge, or turn the air bag off if the car is driven with the seat positioned all the way forward, being the seat lowering kit moves the seat all the way to the rear, the sensor will report the correct seat position. Also you will need to leave the pressure senor under the seat as-is.
*** All this information is a mute point though because you will be totally liable for the failure should you install this seat lowering kit. *** Â
(0 reviews)$332.00 Select options -
Viper Parts
IPS13X Shifter Knob Lowering Kit 92-17 Vipers
Viper Shifter Knob Lowering Kits
Direct bolt-in and will work with the stock factory knob, or an aftermarket shifter knob using 1/2-20 UNF threads. These lowering kits replace the factory black isolator and come in two versions 1″ or 2″ lowering kits.
Youtube Install Video : https://www.youtube.com/watch?v=VZHgzXROSEs Thanks to Life at Speed
(0 reviews)$41.00 Select options
Reviews
There are no reviews yet.