IPS173-GEN 4/5 Billet Pulleys 08-17 Vipers

Related products

• 

  • 
  • 
  • 

  Viper Parts

  IPS164X – Viper Gen 4/5 Pedal Extension Kits

  Pedal Extension Kit for 2008-2017 Vipers

  The Gas Pedal kit moves the pedal 3/4″ toward the driver to improve the heel & toe position between the Throttle & Brake pedals.

   

  The Brake & Clutch pedal Kits move the pedal 1 1/4″ toward the driver to make it easier to disengage the Clutch fully or makes pressing the Brake pedal easier if you can’t get enough adjustment with the factory pedal adjuster.

  All Kits Take less than 15 minutes to install.

  (0 reviews)

  $36.00 – $42.00 Select options This product has multiple variants. The options may be chosen on the product page
• 

  Viper Parts

  IPS111-XX Viper Billet Hub Centric Wheel Spacer w/o External Hub

  Viper 1/4″, 5/16″, & 3/8″ Thick Hub Centric Wheel Spacer – Fits all Dodge Vipers

  CNC machined from aircraft 6061-T6 Aluminum, available in 1/4, 5/16, & 3/8″ thick, 6 X 4.50 bolt pattern.

  All of our wheel spacers are hub centric, as they register on the bearing hub not the wheel studs. We have two versions of our wheel spacers ¼” to 3/8″ which are too thin to support an external hub, and a spacer that has an external hub. As the Viper has a bearing surface that the spacers or wheel ride on, that is 3/8″ long, you can see there is no way to have an external hub the same size as the internal bore needed to fit on the bearing hub on any spacer less than 3/8″. Our wheel spacers with the external hub start at .420″ thick and go up from there to insure there is enough material to support the wheel and not be knocked off due to a thin web between the internal bore and external hub.

  Sold as singles

  Rated 5.00 out of 5

  (1 review)

  $42.00 Select options This product has multiple variants. The options may be chosen on the product page
• 

  Viper Parts

  IPS143X Seat Lowering Kit Fixed 2″ – 03-10 Vipers

  Seat Lowering Kit – Fixed 2″  03-10 Vipers

  This fixed seat lowering kit lowers the 03-10 SRT seat a full 2 inches, allowing extra knee room and headroom for even the tallest Viper driver. The seat will no longer slide forward or backwards, but the seat back can be tilted.

  This is a custom made part, lead time is one week.

  2008-2010 owners *** IMPORTANT AIRBAG FACTS ***

  Decision regarding seat lowering and air bag operation for both seats on 08-10 SRT10 Vipers.

  Both passenger seats have a new system in the Viper that will correctly determine the weight of an occupant and adjust the airbag to on or off. It has some criteria to be met though as it is MUCH more advanced than any system has been before it.

  Between 65 and 105 pounds the system will determine the need for the airbag at all. This will be based on a correctly seated person! This is true for all the levels of adjustment. You must sit in the seat correctly and distribute your weight evenly in the seat without leaning for/aft or side to side. Within seconds after starting the car the system will “lock in” your values. If this is not done correctly and the light is incorrect for your weight it is best to exit the running vehicle and wait 2-6 minutes before re entering the vehicle. At 2 minutes the corrected value is 80% and as the minutes increase to 6 minutes the corrected percentage gets closer to 100. The system also monitors and updates your weight and “position” in the vehicle every 2 minutes after that.

  At 120+ pounds the airbag will still be monitored by the system but will be in the ON mode. It is still critical that your weight is evenly distributed though as it senses this every 2 minutes.

  This all being said if you install the seat lowering kit you will need to do the following:

  Both seats have a position sensor located under the seat, that controls the air bag by proximity to the steering wheel for force adjustment.
  If the seat is lowered and the switch is not installed correctly the force of the airbag is unknown but it WILL still deploy if the conditions are met for it.

   The seat position sensor (a metal proximity sensor), will need to be adjacent to metal when the seat is from midway to the far back position, so you will need to zip tied it to the metal frame of the seat. The purpose of this sensor is to either reduce the air bag charge, or turn the air bag off if the car is driven with the seat positioned all the way forward, being the seat lowering kit moves the seat all the way to the rear, the sensor will report the correct seat position. Also you will need to leave the pressure senor under the seat as-is.

  *** All this information is a mute point though because you will be totally liable for the failure should you install this seat lowering kit. ***  

   

  (0 reviews)

  $332.00 Select options This product has multiple variants. The options may be chosen on the product page
• 

  • 
  • 
  • 

  Viper Parts

  IPS30X-X Big Brake Bracket Kits – for GEN 2

  SRT10 Caliper Mounting Kits – Front & Rear for GEN 2 Vipers (96-02)

  Kit 1) IPS301 Big Brake Bracket kits for Front using SRT10 front caliper and SRT10 14″ front rotors. Includes mounting hardware. This kit is for Vipers with 18″,19″ & 20″ after market wheels, 18″ OEM wheels require 5/16″ thick wheel spacers and ET Lug nuts.

  Kit 2) IPS302 Big Brake Bracket kits for Rear using SRT10 rear caliper and SRT10 14″ front rotors. Includes mounting hardware. This kit is for Vipers with 18″,19″ & 20″ after market wheels, 18″ OEM wheels require 5/16″ thick wheel spacers and ET Lug nuts.

  Kit 3) IPS304 Big Brake bracket kit for Rear using Gen 2 Front calipers and Gen 2 13″ Front rotors on rear. Includes mounting hardware. This kit is for Vipers with 18″,19″ & 20″ OEM and after market wheels,

  Calipers and Rotors not included.

  (0 reviews)

  $280.00 Select options This product has multiple variants. The options may be chosen on the product page