IPS154 Spare Tire Adapter

Related products

• 

  • 
  • 
  • 

  Viper Parts

  IPS173-GEN 3 Billet Pulleys 03-06 Vipers

  Gen 3  Billet Pulleys 03-06 Vipers

  Idler Pulley

  Replaces the Factory Steel Pulley with a Billet Aluminum Pulley with a replaceable Bearing.

  Belt Tensioner Pulley

  Replaces the Factory Plastic Tensioner Pulley with a Billet Aluminum Pullet with a replaceable Bearing.

  Under Drive Crank Pulley

  Pulley is designed to turn water pump, Alternator, Power Steering pump, & AC 25% slower. This results is a 5-10HP gain and keeps the water pump from cavitation problems, and includes new 5/16-18 Grade 8 mounting hardware.

  (0 reviews)

  $72.00 – $185.00 Select options This product has multiple variants. The options may be chosen on the product page
• 

  • 
  • 
  • 

  Viper Parts

  IPS426 Short Throw Shifter 1992-2010 Vipers

  The IPSCO Short Throw Shifter (STS), is designed to reduce the distance your hand needs to move to engage the next gear, thus reducing the amount of time spent shifting, reducing wasted time between shifts, and resulting in improved performance. We have decreased throw by reducing the angle that the shifter shaft travels through during its stroke between gears. IPSCO’s design changes the pivot point geometry of the short shifter from the stock factory shifter to reduce the distance that the upper section must travel to achieve the same degree of movement in the lower section where the shift rod engages. This ensures that although your hand is moving a shorter distance, the transmission is still fully engaged in every gear, and is carefully designed to create the optimal throw length, angular shift throw, and shift knob height. The design also includes springs to help users accurately move from gate to gate, to help prevent missed shifts and over revving of the engine on down shifts. The end result is a shorter, precise shift, which requires a shorter hand movement to engage the next gear, and looks and feels sportier.

  Rated 5.00 out of 5

  (3 reviews)

  $410.00 Select options This product has multiple variants. The options may be chosen on the product page
• 

  Viper Parts

  IPS143X Seat Lowering Kit Fixed 2″ – 03-10 Vipers

  Seat Lowering Kit – Fixed 2″  03-10 Vipers

  This fixed seat lowering kit lowers the 03-10 SRT seat a full 2 inches, allowing extra knee room and headroom for even the tallest Viper driver. The seat will no longer slide forward or backwards, but the seat back can be tilted.

  This is a custom made part, lead time is one week.

  2008-2010 owners *** IMPORTANT AIRBAG FACTS ***

  Decision regarding seat lowering and air bag operation for both seats on 08-10 SRT10 Vipers.

  Both passenger seats have a new system in the Viper that will correctly determine the weight of an occupant and adjust the airbag to on or off. It has some criteria to be met though as it is MUCH more advanced than any system has been before it.

  Between 65 and 105 pounds the system will determine the need for the airbag at all. This will be based on a correctly seated person! This is true for all the levels of adjustment. You must sit in the seat correctly and distribute your weight evenly in the seat without leaning for/aft or side to side. Within seconds after starting the car the system will “lock in” your values. If this is not done correctly and the light is incorrect for your weight it is best to exit the running vehicle and wait 2-6 minutes before re entering the vehicle. At 2 minutes the corrected value is 80% and as the minutes increase to 6 minutes the corrected percentage gets closer to 100. The system also monitors and updates your weight and “position” in the vehicle every 2 minutes after that.

  At 120+ pounds the airbag will still be monitored by the system but will be in the ON mode. It is still critical that your weight is evenly distributed though as it senses this every 2 minutes.

  This all being said if you install the seat lowering kit you will need to do the following:

  Both seats have a position sensor located under the seat, that controls the air bag by proximity to the steering wheel for force adjustment.
  If the seat is lowered and the switch is not installed correctly the force of the airbag is unknown but it WILL still deploy if the conditions are met for it.

   The seat position sensor (a metal proximity sensor), will need to be adjacent to metal when the seat is from midway to the far back position, so you will need to zip tied it to the metal frame of the seat. The purpose of this sensor is to either reduce the air bag charge, or turn the air bag off if the car is driven with the seat positioned all the way forward, being the seat lowering kit moves the seat all the way to the rear, the sensor will report the correct seat position. Also you will need to leave the pressure senor under the seat as-is.

  *** All this information is a mute point though because you will be totally liable for the failure should you install this seat lowering kit. ***  

   

  (0 reviews)

  $332.00 Select options This product has multiple variants. The options may be chosen on the product page
• 

  Viper Parts

  Billet Sway Bar Caps & Polyurethane Bushing Set

  Billet Viper Front and Rear  Sway Bar Caps & Polyurethane Bushing 1992-2017 Vipers

  These brackets are CNC machined from billet 6061-T6 aluminum and anodized clear to give a long lasting protective finish. Supplied with ENERGY SUSPENSION’s performance polyurethane bushing, these bushings are impregnated with graphite to add a lubrication property to the bushings. Complete with a zerk fitting, which utilize a unique channel design to allow grease to flow to all inner bushing surfaces, virtually eliminating any possibility of squeaking.

  SOLD as a Set of 2 

   

  (0 reviews)

  $103.00 Select options This product has multiple variants. The options may be chosen on the product page